Utility emergency plans are designed to protect the grid, not the crop inside a greenhouse. That distinction matters because a greenhouse’s fans, pumps, irrigation, heating and environmental controls can all lose power at the same time, often with only minutes of warning. The article’s central warning is straightforward: utilities plan for that day in detail, but most greenhouses do not.
In California, the utility bill carries a detail many growers overlook: a rotating outage group or block. It shows where a customer stands in line if the grid runs short. Every grower has a place in that line, whether or not the information is printed on the bill. Federal reliability standards, including NERC’s EOP-011, require grid operators nationwide to maintain emergency plans for cutting load. California is unusual in printing the group directly on the utility bill, but the underlying risk is not confined to one state.
When an emergency load-shedding plan is implemented, power is shut off systematically, often with only minutes of notice. Critical facilities such as hospitals are protected where possible. Almost everyone else, including a greenhouse, remains exposed. Rolling outages have hit several regions in recent years during heat waves and winter storms. For a grower, the consequence is not an inconvenience measured in lost lighting hours; it is a simultaneous loss of the equipment that manages temperature, humidity, water and crop protection.
Outage versus curtailment
The difference between an outage and a curtailment is control. In an outage, everything stops at once. In a planned curtailment, the grower decides in advance which loads drop, by how much, and which stay on to protect the crop. A curtailment plan is therefore a written playbook for the hours when the grid is stressed. It does not prevent the utility from acting, but it gives the operation a prepared response instead of an improvised one.
The source material describes four practical steps. They are operational rather than theoretical, and each depends on information the grower already controls.
- Inventory the loads. List major equipment and roughly how much power each piece draws: supplemental lighting, fans, evaporative cooling, heating, pumps, dehumidification, controls and any cold storage. The value of the list is not precision for its own sake; it establishes what can be switched, dimmed, staggered or protected.
- Sort loads by crop risk. Some loads can drop entirely for a few hours with no harm to the crop. Some can be reduced, such as dimming lights, staggering fans or adjusting a setpoint by a few degrees. Some must stay on no matter what, including controls, alarms and whatever keeps the most sensitive crop alive. The sorting depends on what is grown and its stage, so it can change through the season.
- Use forecasts and public alerts as triggers. An outage order may arrive with minutes of notice, but heat waves and cold snaps are forecast days ahead, and grid operators usually issue public alerts before an emergency. Growers with a plan treat those signals as the starting point. In summer, that can mean pre-cooling in the morning, irrigating early and closing shade curtains before the afternoon peak. In winter, it can mean heating ahead of the cold peak, closing thermal curtains early and making sure backup heat is fueled and tested. Either way, the crop enters the hard hours with some margin.
- Assign decisions and automate where possible. Decide who receives the alert, who makes the decision and who carries it out. If the environmental controller can run the sequence automatically, program it and test it. A plan that depends on one person answering a phone at 4 p.m. on a Saturday is not a plan.
After those steps, the grower should know how many kilowatts can be given up, for how long, and at what cost to the crop. That number is the basis for a conversation with the grid. It also exposes the boundary of the plan: load reduction is not free if it compromises the crop, and the acceptable trade-off can shift with crop stage, weather and the length of the event.
Demand response and the value of readiness
Before ordering outages, utilities and grid operators will pay customers who agree in advance to cut load. The article explains the logic: a megawatt that disappears on request is cheaper than one bought at emergency prices. That market is demand response. It exists in most of the country, largely so the outage plan never has to be used.
For a greenhouse, demand response turns a defensive exercise into a measurable operating decision. The grower needs to know which equipment can be curtailed, how long the reduction can last and what protection the crop still requires. That is the same information needed for a curtailment playbook. The difference is that demand response can compensate the operation for flexibility that would otherwise be an unmanaged risk.
The limits are equally important. A plan cannot assume that every load is disposable, and it cannot rely on a single person or an untested control sequence. It also cannot treat a forecast alert as a guarantee of timing. The article’s advice is to ask the utility where the site falls in its plan and then start making an independent plan. For growers, the useful conclusion is not that outages can be prevented. It is that the greenhouse can decide in advance what stops, what dims, what stays on and who is responsible when the grid runs short.
